Jura Giga X8c Professional - Hose sizes for hose replacement

    • Jura Giga X8c Professional - Hose sizes for hose replacement

      Hersteller: Jura | Typ-/Modell: Giga X8c Professional | ca. Baujahr: 2017

      I just acquired this machine and looks like someone did hose replacement on it... no idea why ?(
      Needless to say the job they did is terrible, using cheap plastic hose that is stiff, kinking, and every connection has clamp on it.
      Can someone please tell me the correct pant size for the job?
      Are they all the same from what you can see?
      I assume these are all low pressure connections so silicone hoses, and no clamps needed right?

      Another of topic question,
      what is the connector in the compartment on the back side of the machine for? (beside the power connector and main switch)

      Thank you!

      Here is hose list for this machine komtra.de/jura-satzteile/jura-…egorie&ag=995195&cat=1007





      Mechanische Kenntnisse vorhanden: JA | Elektrische Kentnisse vorhanden: JA | Messgerät vorhanden: JA

      Dieser Beitrag wurde bereits 3 mal editiert, zuletzt von Lifeisfun ()

    • This ist the right hose:
      komtra.de/jura-ersatzteile/jur….0xwd2.0mm-meterware.html

      No clamps are needed for this hoses.

      Look where the cable is connected to the board and
      write here whats the connector designation at the board
      like „CM4E“.
      Immer logisch und Schritt für Schritt vorgehen. Blinder Aktionismus kostet Zeit und Geld.
      Küche: Jura GIGA 5 Pianoblack-Chrom Bj: 2012
      Büro: [sJura GIGA X3 ALU Bj: 2014

    • BlackSheep schrieb:

      This is the right hose:
      komtra.de/jura-satzteile/jura-….0xwd2.0mm-meterware.html

      No clamps are needed for these hoses.

      Look where the cable is connected to the board and
      write here what's the connector designation on the board
      like “CM4E”.
      Thank you!
      The connector is marked CM4F

      Also found these two loose in different spots inside, any idea what is it for?

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von Lifeisfun ()

    • Never seen this.

      The cable ist for „CCU PCB“ - no idea what is it for:
      Seems you can connect some of the following:
      - MCU
      - VDD,GND, RX/TX (3.3V) from MAIN !
      - 5V linear regulator
      - MDB interface
      - Milksensor jack
      - LAN
      - No NRI !!!
      - D-Sub connector
      Immer logisch und Schritt für Schritt vorgehen. Blinder Aktionismus kostet Zeit und Geld.
      Küche: Jura GIGA 5 Pianoblack-Chrom Bj: 2012
      Büro: [sJura GIGA X3 ALU Bj: 2014

    • Never seen this.

      BlackSheep schrieb:


      The cable is for “CCU PCB” - no idea what is it for:
      Seems you can connect some of the following:
      -MCU
      - VDD,GND, RX/TX (3.3V) from MAIN!
      - 5V linear regulator
      - MDB interface
      - Milk sensor jack
      - LAN
      - No NRI!!!
      - D-Sub connector
      Perhaps someone was working on several things at the same time and I got extras :D

      Interesting, thank you!
      must be for some kind of module since the compartment is shaped like a drawer and there is locking clip at the very back of it.
      INFO-VIDEO

    Hilfe zur selbstständigen Reparatur von Kaffeevollautomaten (Jura, Delonghi, Siemens u.v.m.)