Suchergebnisse
Suchergebnisse 1-20 von insgesamt 1.000. Es gibt noch weitere Suchergebnisse, bitte verfeinern Sie Ihre Suche.
-
Jura Giga 5 - Jura Giga screen polishing after shipping damage? Spraying or wrapping alu parts?
BeitragDon‘t try something with the skin of the acrylic. Only try to polish it… but also this could cause additional damage…
-
F90 - eines der schönsten Geräte die Jura je gebaut hat…
-
D4 gibt es doch noch - und ja, das ist optisch „Geschmackssache“, aber die zu kleine Tassenauflage ist einfach nur ein Fault…
-
Hallo, wir im Forum haben mit dem Shop nichts zu tun. Somit existiert kein „kleiner Dienstweg“. Wenn es fragen zur Verkaufsartikeln gibt, geht das ausschließlich über das Forum. Gruß BS
-
Ich hatte auch „relativ weit“ entfernt geschrieben und nicht nur „etwas falsch“. Meinst Du ich sollte das noch deutlicher schreiben?
-
Jura Giga 5 - Jura Giga screen polishing after shipping damage? Spraying or wrapping alu parts?
BeitragYou are developing into a GIGA specialist. There comes one after the other I try to treat display damage like this with acrylic glass polish - it's a very time-consuming process - but it usually gets better. The problem with the rotary boxes is that they have a “protective layer” over the actual acrylic (or is it multi-layered?) How this will behave in the end is therefore even less predictable. If the anodized layer of the ALU has become so rotten in the dishwasher, you can no longer get rid of…
-
Den Wassertankdeckel und den Pulverdeckel muss man nicht vorher entfernen - das geht beim Zerlegen einfach so mit weg - und man läuft nicht Gefahr etwas kaputt zu machen.
-
Also dann eher in der Richtung? Jura Brüheinheit steht nach dem Einbau nicht exakt in Grundstellung - Brühkammer nicht mittig unter Pulvertrichter
-
Das DV ist nicht grundsätzlich ausgeschlossen. Es ist laut Herstellerdefinition auch ein Teil des Antriebs und bei einem neuen Antrieb ist auch immer das DV dabei.
-
Es wurde nicht nur geschrieben, dass es nicht solange hält, sondern dass es schon zum Start weg schlechter ist als die Originalsteine - das kann man doch nicht überlesen… Der hier abgebildete Aroma+ Mahlkegel hat auf jeden Fall nichts mit dem zuerst gezeigten zu tun… Mache mal ein Bild von der Oberseite des schwarzen Teils mit den 3 Mitnehmernasen. Und auch eines von der Seite des neuen Mahlrings.
-
Hallo. Es gibt mindestens 3 Möglichkeiten. Mahlwerk: Zuviel oder zuwenig Kaffeemehl in der Brüheinheit Antrieb: Einen defekten Motor, defekten Microschalter, klemmenden Antrieb oder Montagefehler Brüheinheit: Montagefehler oder mechanischen Defekt Bevor wir nicht den Verursacher des Problems identifizieren gibt es zuviele Möglichkeiten, als dass man sie alsTipps auch nur alle aufzählen könnte. Du musst zunächst versuchen festzustellen was des Problems verursacht. Gruß BS
-
Die meisten hier bevorzugen Kunststoffstößel, da die Messingstößel auch ihre Probleme haben klnnen. Deswegen die Empfehlung von Harry keines mit Messingstößel zu nehmen.
-
Sehr schön, das weiter Zerlegen ist aber eigentlich denkbar einfach. man muss nur die zwei T10 Schrauben entfernen und im Fuß die Kabel aus den Klemmungen lösen dann geht der komplette Kopf ab.
-
Zitat von Lifeisfun: „And those 2 LEDs are just pressed into the black plastic ? “ I don't know because I've never had to change one. But for such purposes I have a defective complete unit (fabric tape torn and missing) that I can try around with. I play around with it to practice when I need to do something on the unit. Zitat von Lifeisfun: „You Europeans are so lucky to get recycled parts so easy! “ But only via eBay or a single, special (unfortunately very unreliable) dealer.
-
Saeco (by Philips) SM7580/00 - Xelsis Klavierlack Schwarz - Kein Milchschaum trotz neuen Ventilen
BlackSheep - - Saeco (by Philips) • Reparatur • Wartung • Pflege
BeitragZitat von Sniper0015: „Hat denn niemand eine Idee ? “ Sorry - Momentan wohl eher nicht - sonst hätte sich schon wer gemeldet.
-
The 4 screws at the back are not enough. There are additional 2 screws from behind. To open this the whole coffee spout unit has to get removed from the machine and has nearly complete disassembled (also the sliding fabric etc. has to be removed) to get to the 2 screws.
-
It looks like you have enough knowledge of electronics. Can you please send a picture showing the replaced part on the board?
-
Perhaps RolandM can say something. I don‘t know which plate-vias are the problem and corroded. I thought I understood the problem is located at the Rotary-Plate…